Search found 9 matches

by creighton
03 Dec 2019, 03:25
Forum: Software
Topic: How to pass values from RevPi7 to Modbus TCP
Replies: 3
Views: 3333

Re: How to pass values from RevPi7 to Modbus TCP

Hi Dirk,

Is there any updates on this?

Regards,
Creighton
by creighton
08 Nov 2019, 03:53
Forum: Software
Topic: How to pass values from RevPi7 to Modbus TCP
Replies: 3
Views: 3333

How to pass values from RevPi7 to Modbus TCP

Hi,

I am able to receive values from my s71200 by using RevPi7 . How do I pass these values to Modbus TCP?

Is it possible to pass the values from RevPi7 to any of the virtual modules provided in Pictory?

Hope to receive some feedback regarding this matter. Thank you.

Best regards,
Creighton
by creighton
17 Oct 2019, 05:11
Forum: Software
Topic: Communication with S7-1200
Replies: 8
Views: 9361

Re: Communication with S7-1200

Hi, I am also trying to do the same. May I know are you able to receive the values from the PLC and read it by using the Modbus module? I have already programmed the PLC s71200 and assigned a DB. Can you show me an overview on how to configure the revpi 7 to establish a connection with the PLC? I kn...
by creighton
13 Sep 2019, 12:05
Forum: Hardware
Topic: Cannot output monitor display
Replies: 3
Views: 3495

Re: Cannot output monitor display

Hi Dirk,

Thank you for your solutions. I tried writing my original image into the device which I have backed up earlier and it is working now.

Thank you.

Regards,
Creighton
by creighton
11 Sep 2019, 09:01
Forum: Hardware
Topic: Cannot output monitor display
Replies: 3
Views: 3495

Cannot output monitor display

Hi, The RevPi was working normally until when I rebooted using the terminal by typing "sudo reboot". The problem that occurred is that my monitor stops receiving hdmi signal from the RevPi. Therefore, I cannot see any output displayed in my monitor at all. I have tried to access the config...
by creighton
24 Jul 2019, 04:36
Forum: Software
Topic: Revolution Pi Booting Failure
Replies: 8
Views: 6808

Re: Revolution Pi Booting Failure

Hi Amar, Thank you for your time and suggested solutions. By the way, I have repeated the whole process again by writing the stretch image to the RevPi by using Win32DiskImager. Before I did that, I only used the SD Card Formatter to overwrite format my RevPi so that I can write the image to it. Aft...
by creighton
22 Jul 2019, 08:31
Forum: Software
Topic: Revolution Pi Booting Failure
Replies: 8
Views: 6808

Re: Revolution Pi Booting Failure

Hi Amar, As I was done writing the image and started booting the RevPi, the same problem occurred with the last kernel message showing: "[ 1.6152451 ---[ end Kernel Panic - not syncing: VFS: Unable to mount root fs on unknown block(179,2) ]----. I have no cables connected to my RevPi except the...
by creighton
10 Jul 2019, 03:03
Forum: Software
Topic: Revolution Pi Booting Failure
Replies: 8
Views: 6808

Re: Revolution Pi Booting Failure

Hi Dirk, Thank you for getting back to me. After writing the stretch image in my RevPi Connect, when I start it, it does not bring me to any login screen, it is black screen that just ran a few program lines and stop there as if it has stopped. May I know how to attach image as a reference to my iss...
by creighton
09 Jul 2019, 05:30
Forum: Software
Topic: Revolution Pi Booting Failure
Replies: 8
Views: 6808

Revolution Pi Booting Failure

Hi, I am facing some issue in booting the KUNBUS Revolution Pi that we recently purchased. I have performed the following steps to configure the Rev Pi and the following errors produced accordingly. 1) I have followed this tutorial 01- Creation of Image, https://revolution.kunbus.com/tutorials/video...